Cheboksary, Russian Federation
In the paper there are emphasized problems connected with the use of diamond metal bond abrasive discs at the processing of hard alloys. The reasons of cutting capacity decrease are pointed out which limit a wide-spread use of a diamond metal bond tool. It is established that for the achievement of a required productivity and quality of ready products is possible at the expense of the application of electro-chemical and electro-physical methods of stropping and also due to the improvement of abrasive disc designs. This work reports the investigations of a cutting capacity of diamond discs at the working of hard alloys by a combined method of electro-chemical grinding with simultaneous continuous stropping. As an output parameter there was accepted a cutting capacity factor of a diamond which was assesses according to the changes in effective working capacity. On the basis of the results of the experimental data processed there were obtained theoretical models of the dependence of the cutting capacity factor upon electric and mechanical constituents of the modes of combined electro-chemical grinding. A complex of investigations directed to the detection of efficient modes ensuring the stability of cutting capacity in diamond metal bond discs is carried out. It is experimentally confirmed that the application of the method of combined electro-chemical grinding with the simultaneous continuous disc stropping at working hard alloy materials allows increasing diamond disc cutting capacity by 15% in comparison with other methods of the diamond working of such materials.
grinding, metal bond, cutting capacity of diamond discs, hard alloys, diamond abrasive disc.
1. Popov, А.Yu., Rechenko, D.S., Vasiliev, Е.V., Sergeev, V.S., Koltsov, А.G. Diamond grinding technology for hard alloy products // Bulletin of Ufa State Aircraft Technical University. - 2012. - Vol. 16. - № 4 (49). - pp. 24-29.
2. Vasiliev, Е.V., Popov, А.Yu., Rechenko, D.S. Diamond grinding of hard alloy plates // Bulletin of Mechanical Engineering. - 2012. - Vol. 32. - № 11-12. - pp. 730-732.
3. Suslov А.G. Improvement and development of competitive techniques ensuring quality increase of engineering products // Bulletin of Bryansk State Technical University. - 2006. - № 2. - pp. 24-29.
4. Yanyushkin, А.S., Lobaniov, D.V., Kovalevsky, S.V. Quality increase in preparation of hard alloy tool // Systems. Methods. Techniques. - 2009. - № 1. - pp. 95-98.
5. Rychkov, D.А., Skripnyak, V.А., Yanyushkin, А.S., Lobanov, D.V. Cutting edge formation in milling tool for working laminated composites armored with glass fibers // Systems. Methods. Techniques. - 2014. - № 2 (22). - pp. 42-46.
6. Lobanov D.V., Yanyushkin А.S., Kuznetsov А.М. Drawbacks in common methods of hard alloy tool sharpening and ways for their improvement // Proceedings of Bratsk State University. Series: Engineering Sciences. - 2004. - Vol. 2. - pp. 95-98.
7. Yanyushkin A., Lobanov D., Arkhipov P., Ivancivsky V. Contact processes in grinding // Applied Mechanics and Materials. 2015. Т. 788. С. 17-21.
8. Arkhipov, P.V., Yanyushkin, А.S., Kovalevsky, S.V. On nature of abrasive disc glazing // Proceedings of Bratsk State University. Series: Natural and Engineering Sciences. - 2008. - № 2. - pp. 169-174.
9. Yanyushkin, А.S., Lobanov, D.V., Bataev, V.А., Arkhipov, P.V., Medvedeva, О.I. Investigations of diamond disc operational capacity at composites processing // Systems. Methods. Technologies. - 2010. - № 7. - pp. 87-91.
10. Yanyushkin, А.S., Popov, V.Yu., Yanyushkin, R.А. Elements of grinding machine updating for electro-diamond processing // Proceedings of Bratsk State Technical University. Series: Natural and Engineering Sciences. - 2000. - Vol. 1. - pp. 189-190.
11. Yanyushkin, А.S., Lobanov, D.V., Arkhipov, P.V., Popov V.Yu. Investigations of electric mode impact upon qualitative and economic indices of combined electro-diamond processing of hard alloy materials // Science Intensive Technologies in Mechanical Engineering. - 2015. - № 3(45). - pp. 22-29.
