VAK Russia 05.02.08 UDC 62 CSCSTI 55.13

TOOTH LEG EXCESSIVE UNDERCUT ELIMINATION IN HELICAL CYLINDRICAL GEARS WITH PROTUBERANCE OF HOBBING CUTTER BASED ON GRAPHIC RUN-IN

Published in Bulletin of Bryansk state technical university · Issue 7, 2021 · Pages 19–27 · Rubric: Mechanical engineering
DOI: https://doi.org/10.30987/1999-8775-2021-7-19-27
Received: 16.06.2021 Accepted: 30.07.2021 Published: 30.07.2021 Language of publication: ru-RU
In the paper there are considered procedures for designing a transition curved tooth leg of helical cylindrical gears. A significant parameter of a transition curve is a diameter of boundary points. The boundary point diameter belongs to a bottom point of the involute profile of the teeth side surface of a gear ring. The boundary point position must be lower of the design end point of the involute profile defined by the designer of gearing. A diameter value depends upon a great number of production factors: a profile and wear of a grinding disk, setting up parameters, teeth machining modes of a gear ring, but it is impossible to ensure the specified values of the diameter of boundary points without a correct design solution in the course of the form choice of milling cutter protuberance. The solution on protuberance acceptable parameters of a gear-cutting tool is made by the designer of a cutter during graphic run-in fulfillment. In the paper there are revealed conditions under which arise mistakes in the course of graphic run-in fulfillment within the limits of one teeth pitch of a milling cutter. There are shown recommendations for the fulfillment ensuring the diameter dimension of boundary points of the transition curve specified by the designer of gearing. The data on the design parameter impact of the hob protuberance upon the continuance of cutting edge interaction are shown. There are recommendations given to prevent undercut arising caused by the fulfillment of graphic two-dimensional run-ins of cylindrical helical gears. The work purpose: the elimination of tooth leg excessive undercut in helical cylindrical gears with the protuberance of a worm milling cutter at the expense of the fulfillment of graphic run-in conditions. The investigation methods: the graphical modeling of a run-in process. The investigation results and novelty: there are defined conditions of arising an excessive undercut in the tooth leg of helical cylindrical gears during the fulfillment of graphic run-ins of a tool rack. The conclusions: for mistake prevention in the calculations of the protuberance geometrical parameters of the helical milling cutter the graphic run-in must be carried out not less than on the 1.5 pitch of the milling cutter.
cylindrical gear, graphic run-in, leg, tooth, undercut, operation
Text References
Text (PDF)
Read Download

1. Remnev, A. I. Analiz i sintez metodologii proektirovaniya instrumenta s ishodnoy instrumental'noy poverhnost'yu / A. I. Remnev, O. G. Kretova, N. I. Myachikova, S. V. Shvec, M. S. Voroncova // Vestnik Tambovskogo universiteta. Seriya: Estestvennye i tehnicheskie nauki. - 2016. - T. 21. - №1. - S. 316-324.

2. Balkov, V. P. Sovremennye tehnologicheskie podhody pri izgotovlenii cilindricheskih zubchatyh koles v usloviyah melkoseriynogo proizvodstva i osobennosti rascheta i proektirovaniya zuboreznogo instrumenta / V. P. Balkov, L. I. Kameneckiy, A. S. Kiryutin, E. A. Neginskiy, O. S. Ott, D. N. Pischulin // Metalloobrabotka. - 2015. № 2 (88). - S. 2-6.

3. Hrytsay, I. Improved method of gear hobbing computer aided simulation / I. Hrytsay, V. Stupnytskyy, V. Topchii // Archive of Mechanical Engineering. - 2019. - Vol. 66. - No 4. - pp. 475-494.

4. Savel'ev, S. V. Vybor optimal'nyh metodov chislennogo proektirovaniya zuboreznogo dolbyaka, prednaznachennogo dlya narezaniya evol'ventnyh koles naruzhnogo zacepleniya / S. V. Savel'ev, D. I. Volkov / / Sovremennye materialy, tehnika i tehnologi. - 2017. - №7 (15). - S. 80-86.

5. Nichkov, A. V. Optimizaciya konstruktivnyh elementov chervyachnoy modul'noy frezy pri zadannyh parametrah narezaemogo zubchatogo kolesa / A. V. Nichkov // Avtomatizaciya. Sovremennye tehnologii. - 2016. - № 11. - S. 7-9.

6. Feofilov, N. D. Raschet kinematicheskih i statisticheskih uglov sbornyh chervyachnyh frez / N. D. Feofilov, S. L. Rahmetov, E. S. Yanov // Izvestiya Tul'skogo gosudarstvennogo universiteta. Tehnicheskie nauki. - 2016. - №4. - S. 178-185.

7. Ryabov, E. A. Sozdanie modeli chervyachnoy zuboreznoy frezy s ispol'zovaniem ekvivalentnoy zubchatoy reyki // E. A. Ryabov, S. Yu. Yurasov, A. G. Kondrashov / Vestnik Izhevskogo gosudarstvennogo tehnicheskogo universiteta im. M.T. Kalashnikova. - 2017. - T. 20. - №2. - S. 82-84.

8. Han, J. Analytical study on tooth profile of non-circular gear based on hobbing process simulation / J. Han, D. Li, L. Xia, X. Tian // ASME 2019 14th International Manufacturing Science and Engineering Conference, MSEC. - 2019. - Vol. 2. - 155261.

9. Vulgakov, E. B. Teoriya evol'ventnyh zubchatyh peredach / E. B. Vulgakov. - Mashinostroenie, 1995. - 320 s.

10. Svidetel'stvo o registracii bazy dannyh RU 2016620243 Baza dannyh dlya avtomatizirovannogo proektirovaniya chervyachnyh zuboreznyh frez i modelirovaniya zubofrezernyh operaciy / Petrov A.I., Reznikov S.S., Tokarev V.V., Akopyan M.G., Kuznecova O.V., opubl. 17.02.2016. Zayavka № 2015621721 ot 31.12.2015.

11. Mihaylov, M. I. Modelirovanie processa obrabotki poverhnosti zubchatogo kolesa chervyachnoy frezoy / M. I. Mihaylov, V. D. Bogackiy // Vestnik Gomel'skogo gosudarstvennogo tehnicheskogo universiteta im. P.O. Suhogo. - 2013. - №2. - S. 31-39.